|
|||||||||
|
|||||||||
| |||||||||
|
|||||||||
|
|||||||||
| |||||||||
|
|
|
| |||||||||
 |
|
|
«
Previous Thread
|
Next Thread
»
|
Thread Tools | Search this Thread | Rate Thread | Display Modes |
Dev Shed Forums Sponsor:
|
|
|
|
#1
January 19th, 2007, 07:01 PM
|
|||
|
|||
|
Motherboard does not reconize harddrive
I have a ASUS P5GDC deluxe motherboard it does not recognize the hard drive.hard drive was tested and is fine,motherboard does recognize the other drives but when connect the hard drive to the other drives cable will not recognize hard drive
|
|
#3
January 20th, 2007, 08:20 AM
|
||||
|
||||
|
Hi tarheel99 and welcome to Dev Shed.
The more information you can give us, the easier it is for us to help you. When you say that other drives can be seen fine, are these hard drives or optical drives ? Is the drive not recognised in the BIOS or is this by the operating system ? If it's the latter, what is the OS that you are using ?
__________________
The No Ma'am commandments: 1.) It is O.K. to call hooters 'knockers' and sometimes snack trays 2.) It is wrong to be French 3.) It is O.K. to put all bad people in a giant meat grinder 4.) Lawyers, see rule 3 5.) It is O.K. to drive a gas guzzler if it helps you get babes 6.) Everyone should car pool but me 7.) Bring back the word 'stewardesses' 8.) Synchronized swimming is not a sport 9.) Mud wrestling is a sport
|
|
#4
January 20th, 2007, 02:39 PM
|
|||
|
|||
|
drive not recongized
Quote:
the os system is windows xp,when the system boots it shows operating system not detected or corrupt,I rebooted with disc to repair did not work,I had hard drive tested was ok I attached a new hard drive and system did not show hard drive but the rw and dvd drive did show.attached hard drive to one of these drives and did not show tried different conf still did not show
|
|
#5
January 20th, 2007, 03:47 PM
|
||||
|
||||
|
Is this an IDE drive ? Have you ensured that the jumpers on the drive are set correctly ?
|
|
#6
January 22nd, 2007, 09:23 AM
|
|||
|
|||
|
Quote:
yes is IDE drive, jumpers are set same as when was working correctly any suggestions
|
|
#7
January 22nd, 2007, 10:46 AM
|
||||
|
||||
|
Have you tried a different IDE cable ?
|
|
#9
January 23rd, 2007, 08:40 PM
|
||||
|
||||
|
Quote:
Sorry, not sure if I'm following correctly... This HD was working properly at one point? When you say it was tested, how was it tested?
|
|
#10
September 24th, 2007, 09:40 PM
|
|||
|
|||
|
hey th99
what kind of drive make/model is it? so, I can check manuf. jumper settings. what do jumper settings on the rear of YOUR drive look like? Show them like this below where this | is a jumper block. [::::::::::::::::::::] [:|:::] {oooo} How many drives are on that IDE cable when your system will not boot nor recognize the drive(s)? one? two? If two, what do jumper settings on the rear of the OTHER drive look like? Show same as above diagram.
|
|
#11
September 24th, 2007, 09:42 PM
|
||||
|
||||
|
Is the drive a brand new drive? It might need to be formatted before you can use it.
|
|
#12
September 24th, 2007, 09:45 PM
|
|||
|
|||
|
Hey th99,
you may want to read this: http://www.pcguide.com/ref/hdd/if/ide/conf_Cable.htm just a refresher about drive configurations.
|
|
#13
September 24th, 2007, 09:53 PM
|
||||
|
||||
|
Quote:
You guys do realize that this is a 9 month old thread, right? It was dug up by someone a few days ago inquiring about another problem altogether, so seriously doubt the original OP still has the problem. Just my two cents though. @sindbadmourad: As for a pdf to repair motherboards and such, there is not one generic pdf that will encompass this. If you have a particular make, model, brand, etc, then you can visit the manufacturer's website to pull up info on that particular model.
|
|
| Viewing: Dev Shed Forums > Computer Hardware > Motherboards > Motherboard does not reconize harddrive |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
Del.icio.us
Digg
Google
Spurl
Blink
Furl
Simpy
Y! MyWeb
Linear Mode
